Measure both feet. If one foot is slightly larger than the other, select a size that fits the larger of the two.
Consider the type of socks you’ll be wearing with your boot. For thicker socks, you may want to select a half size larger than you normally wear.
When you do receive your boots, we recommend first wearing them indoors for a few hours to ensure they’re the right fit.
TURTLESKIN GLOVE SIZING
To make sure you get the best comfort, protection, and satisfaction, TurtleSkin Glove sizes are based on accurate hand measurements. TurtleSkin Gloves come in many sizes to best fit you. Please use these charts to find your best glove size. NOTE:Use the longest "finger length" or "hand width" measurement to find your size. If your longest measurement falls between sizes, order the larger size.
Hand Width Measurement:Wrap a tailor's measuring tape around your dominant hand just below knuckles, excluding your thumb, and make a fist. This measurement is your "hand width" glove size.
Sizes
6-7 inches
XS
7-8 inches
S
8-9 inches
M
9-10 inches
L
10-11 inches
XL
11 plus inches
XXL
Finger Length Measurement: Measure from the bottom edge of your palm to the tip of your middle finger to determine your "finger length" size.
Sizes
6 5/16 inches
XS
6 3/4 inches
S
7 3/16 inches
M
7 9/16 inches
L
8 1/16 inches
XL
8 7/16 plus inches
XXL
If you have any questions about measuring your hand, please call us at 603-291-1000 (Mon-Fri 9am to 5pm, EST)
***The MOPC carrier is backordered by up to 30 days. This message will be updated as the situation changes. A reasonable alternative to the MOPC is the BAO Tactical Dynamic Plate Carrier.
Due to increased demand these plates they are on back order. We have 2000 plates in production shipping to us in shipments of 200-400 to be able to fulfill your orders as quickly as possible. We are shipping them on a first come first serve basis. Lead times are pending and are based on the speed we receive these shipments.***
Modular Operator Plate Carrier Level IV Active Shooters Kit
As of right now, Body Armor Outlet is only offering MOPC Active Shooter Kits in black.
These kits consist of one MOPC Carrier and two (2) Level IV 4401 10"x12" Shooter's Cut Hard Armor Plates.
The Modular Operator Plate Carrier
Condor's Modular Operator Plate Carrier was designed for modular attachments on all sides, as well as for functionality and operator mobility. The MOPC accepts up to 10.25" x 13.25" plates front and back, and up to 6" x 8" side plates.
Features:
Emergency drag handle
Removable anti-slip shoulder pads with hook and loop guides
Adjustable shoulder straps
MOLLE webbing for modular attachments
Hook and loop webbing
Front map pocket with snap, hook and loop closure
Breathable 3D Mesh liner
Adjustable cummerbund with built-in plate pockets
Side release buckles on shoulders and internal waist strap
Easy access plate pockets
Ballistic plates/soft armor not included
Imported
Specifications:
Cummerbund Size:
Adjustable from 40" - 48"
Plate capacity:
Side plate compatible up to 6" x 8"
Accepts Medium or Large Swimmer/ESAPI plates up to 10.25" x 13.25"
Shooters SA IV 10x12 .06 Cert Hard Armor Plate - BAO 4401L
Finished with a CORDURA® nylon wrap, the 4401 Series armor is highly durable, water resistant, and has enhanced resistance to tear and abrasions. It can be stored in a vehicle for quick access, so it’s a perfect fit for active shooter scenarios.
The 4401L hard armor plate is certified to the NIJ .06 Level IV Stand Alone standard specifications. It has been made in the form of a single curve shooters cut style which works great as either a front or back plate, allowing for a good range of motion while in a shooters stance.
Features:
Advanced composite materials
Single curve design
Highly durable, water resistant polyurethane coated CORDURA® fabric finish
