Measure both feet. If one foot is slightly larger than the other, select a size that fits the larger of the two.
Consider the type of socks you’ll be wearing with your boot. For thicker socks, you may want to select a half size larger than you normally wear.
When you do receive your boots, we recommend first wearing them indoors for a few hours to ensure they’re the right fit.
TURTLESKIN GLOVE SIZING
To make sure you get the best comfort, protection, and satisfaction, TurtleSkin Glove sizes are based on accurate hand measurements. TurtleSkin Gloves come in many sizes to best fit you. Please use these charts to find your best glove size. NOTE:Use the longest "finger length" or "hand width" measurement to find your size. If your longest measurement falls between sizes, order the larger size.
Hand Width Measurement:Wrap a tailor's measuring tape around your dominant hand just below knuckles, excluding your thumb, and make a fist. This measurement is your "hand width" glove size.
Sizes
6-7 inches
XS
7-8 inches
S
8-9 inches
M
9-10 inches
L
10-11 inches
XL
11 plus inches
XXL
Finger Length Measurement: Measure from the bottom edge of your palm to the tip of your middle finger to determine your "finger length" size.
Sizes
6 5/16 inches
XS
6 3/4 inches
S
7 3/16 inches
M
7 9/16 inches
L
8 1/16 inches
XL
8 7/16 plus inches
XXL
If you have any questions about measuring your hand, please call us at 603-291-1000 (Mon-Fri 9am to 5pm, EST)
Model 701C Chain Link Handcuff - Black Oxide Finish
The classic design. The Model 700 incorporates spun rivet construction for increased strength and durability. Smooth single strand action allows for fast and efficient cuffing. The Model 700 has been approved by the National Institute of Justice. It comes with a lifetime warranty for manufacture defects. Two keys supplied. Made in USA.
Features:
The black oxide finish is designed for low visibility or tactical situations.
Smooth single strand action and spun rivet construction.
NIJ Approved
Lifetime Warranty for Manufacture Defects
Made in USA
Peerless - Setting the Standard Since 1914
Peerlesså¨ Handcuff Company was established in 1914 in Springfield, Massachusetts. Over ninety years later, the classic swing through design of the original Peerlesså¨ handcuff, continues to be the industry standard. Peerless offers a full line of restraints including chain link handcuffs, hinged handcuffs, oversize handcuffs, leg irons, waist chains and color plated restraints. All of our products are designed to meet and exceed the tough U.S. National Institute of Justice standards for strength and quality. All Peerless products are backed by a lifetime warranty for manufacture defects.
Proper Maintenance per Peerless
Use only approved restraining procedures such as the guidelines in our handcuff manual. Frequent review and practice of proper procedures will increase your safety and efficiency. Approved procedures will also help to ensure your restraints continue to function properly. While Peerlesså¨ restraints are designed and manufactured to take abuse avoid dropping onto or banging against hard surfaces. Restraints should receive regular care and maintenance. Inspect them frequently. Keep the ratchet and key hole free of dirt, lint or other foreign substances which may hinder proper functioning. When unlocking your restraint be careful not to torque the key guide post. This will loosen the post causing it to fall out. Also, be careful not to over rotate the key causing the key flag to break off or become stuck in the locking mechanism. Use extra caution when using oversize keys. When possible carry your restraints in a protective case to reduce exposure to outside elements. If exposed to moisture dry thoroughly. Most importantly, dry the inside locking mechanisms.
Warranty with Peerless
Peerlesså¨ Handcuff Company hereby warrants that any restraints manufactured after January 1, 1996 is free of manufacture defects. In case of manufacture defect, Peerlesså¨ Handcuff Company agrees to repair or replace a defective restraint when it is returned to our Springfield, Massachusetts, U.S.A. address. This warranty does not cover damage caused by abuse or ordinary wear and tear of the handcuff, nor any damages whatsoever which may be incurred by reason of any failure to carefully comply with directions as outlined in the manufacturer's instructions. Stamping or etching of identification markings on any part of the restraint after they have left the factory is not recommended and may cause malfunction of product and void warranty.
